Factory quality inspection – Factory inspection and factory inspection are activities of checking and assessing the quality or causes of damage, value, shelf life and other technical parameters of the factory building, workshop part or the whole factory through observation and experiment combined with calculation and analysis according to current standards.
Inspection Vietsum would like to present the purpose of factory inspection:
The purpose of factory quality inspection – Garment factory inspection
1. Factory quality inspection – Inspection of the garment factory to review the entire quality of the existing works up to the present time after many years of construction to give accurate conclusions to the factory owner, the managing agency, the manager. State on the condition of the factory for the following requirements:
2. Verification of conversion of use for factories; Evaluate the load-bearing safety level of the existing work structure using incorrect functions according to the original design;
3. Verification and assessment of the remaining quality of the work due to the breakdown;
4. Verify and determine the quality of the current state, check the cause of the damage, calculate and test the bearing capacity of the workshop when loading more, renovate the floor, raise the floor, change the floor load.;
5. Verification determines the quality of the current situation, determines the remaining quality percentage of each asset;
6. Inventory of current status, determine prices of properties and works attached to land for relocation;
7. Factory inspection – Factory bearing safety certification verification;
8. Factory quality inspection and assessment put into use again, continue to operate;
9. Factory quality inspection for equipment conversion;
10. Verification and assessment of work incidents, determine the causes of bearing capacity determination, assess the safety of structural parts and the entire work.;
11. Factory inspection – Factory quality inspection and assessment to complete the project;
Image of factory quality inspection – Garment factory inspection:
Photo: Check and document size of factory structure – by steel dimension
Photo: Check and record size of factory structure-by steel dimension – Factory inspection
Factory quality inspection method – Garment factory inspection:
FACTORY INSPECTION – FACTORY INSPECTION:
1. Observing and checking the current state of the work: Manually, combined with visual observation, using camera equipment, steel ruler, measuring machine to determine the width of the crack.
2. Checking the geometric dimensions: checking the scene, measuring, redefining the size of the construction components, redrawing according to reality. Made by manual method, direct measurement with steel ruler, clamp ruler.
3. Test of concrete strength: Manually: drilling to take concrete core directly in the field and then machining, compressing at the laboratory, combined with non-destructive method using bounce gun.
4. Check the number and diameter of reinforcement: Electromagnetic method using Elcometer THD 331 machine equipment combined with chisel drilling, manual measurement with clamps.
5. Steel reinforcement protection thickness test: Electromagnetic method using Elcometer THD 331 machine equipment combined with chisel drilling, manual measurement with clamp.
6. Deflection test: Performed by surveying method, using leica electronic total station, measuring and determining the altitude of points, calculating the difference.
7. Check the verticality: Performed by surveying method, using the leica electronic total station, measuring and determining the coordinates of points, calculating and determining the vertical.
8. Check the overall inclination of the project: Performed by surveying method, using a leica electronic total station, measuring and determining coordinates of points, calculating and determining inclination.
INSPECTION IN THE LAS OF CONSTRUCTION:
1. Fabricate concrete samples drilled in the field in accordance with the standard TCXDVN 239: 2006, then compress to determine the strength by Phoenix compressor..
2. Processing data collected in the field: rebound value, deflection value, verticality, overall inclination of the work, … at the laboratory. Use the computer.
3. Calculating and evaluating computer use data through specialized software: etabs, safe, … and related standards.
Photo: Check the weld thickness of the tubular structure with an ultrasonic flow meter.
Photo: Check the thickness of the pipe structure-by a 45MG Ultrasonic thickness machine.
Photo: Test hardness, strength of steel-Mac by NDT-400DL machine.
Photo: Check the steel column for damage by using the steel ultrasonic machine.
Photo: Ultrasonic examination of steel decks for internal defects.
Photo: Ultrasonic test to detect imperfections or defects in the welding of steel structures to the outside.
Photo: Check the thickness and size of steel girder frame, roof purlins for the calculation.
Making report on completion of factory quality inspection – Garment factory inspection:
A. Factory inspection – Making quality inspection report.
B. Analyze documents, experimental data, survey, measure, the actual state of the project.
C. Determine the extent and cause of the breakdown, defect or breakdown (if any); report on quality inspection results and ensure technical requirements in accordance with current regulations.
D. Test calculation with actual data of experiment, survey, measurement and applied load. Bearing capacity of columns, beams, floors, safety of the structure.
E. General assessment of current bearing capacity of the inspected object and the works; propose repair solutions (in case the work is damaged).
Hotline: 090 959 8771 – Mr Nam
– “Vietsum successfully accompanies customers’ workshop” –
